出現“Setup was unable to use the existing partition”錯誤時，通常是因?yàn)榇疟P分區樣式與系統啟動模式不匹配。 1.首先檢查啟動模式（UEFI或Legacy BIOS）和磁盤分區樣式（GPT或MBR），確保兩者匹配；2.使用DiskPart命令清理磁盤，清除舊的分區信息；3.檢查是否有隱藏分區或磁盤鎖定，並清除只讀屬性；4.確認磁盤不是動態磁盤，必要時轉換為基本磁盤。以上步驟按順序處理即可解決該問題。

When you see the error "Setup was unable to use the existing partition" during Windows installation, it usually means something is off with how your drive is set up. It's not a dead end — but you do need to take a few specific steps to fix it.

Here's what typically works:

Check Disk Partition Style: MBR vs GPT

One of the most common causes of this error is a mismatch between your system's boot mode and the disk partition style.

• If your PC uses UEFI , your disk needs to be in GPT format.
• If it's using Legacy BIOS , then it should be MBR .

You can check your current boot mode by pressing Shift F10 during setup to open Command Prompt and typing:

 msinfo32

Look for “BIOS Mode” — if it says UEFI, your disk must be GPT.

If there's a mismatch, you'll need to either:

• Change the boot mode in BIOS/UEFI settings (if possible), or
• Convert the disk from MBR to GPT (or vice versa)

?? Warning: Converting will erase all partitions on the disk, so back up data first if needed.

Use DiskPart to Clean the Drive

Sometimes, old partition info or corrupted structures are the culprit. Using DiskPart to clean the drive often resolves it.

Steps:

• Press Shift F10 to open Command Prompt
• Run these commands one by one:

 diskpart
list disk
select disk X ← Replace X with your disk number
clean
convert gpt ← or convert mbr, depending on your boot mode

After that, exit and restart the installer. The error should go away.

? Note: This wipes all partitions, so make sure you're okay with losing any data on the drive.

Check for Hidden Partitions or Drive Locks

Some drives come with hidden recovery or OS-related partitions that can confuse the installer.

Also, some disks might be locked due to BitLocker or other encryption features.

To check:

• Try viewing all partitions via Disk Management or DiskPart
• Make sure the drive isn't marked as read-only

In DiskPart:

 select disk X
attributes disk clear readonly

This removes the read-only flag and may allow Windows Setup to proceed.

Make Sure You're Not Installing on a Dynamic Disk

Windows Setup doesn't support installing on dynamic disks. If your drive is listed as dynamic in Disk Management, that's why the error appears.

To fix:

• Backup any data
• Convert the disk back to basic using Disk Management or third-party tools

There's no direct way to convert a dynamic disk to basic without deleting volumes, so plan accordingly.

Fixing this error usually comes down to matching boot mode with disk type, clearing out old partition data, and making sure the disk is in a state the installer expects. It's not complicated once you know which part is off.

基本上就這些。

以上是如何修復Windows安裝期間的'設置無法使用現有分區”？的詳細內容。更多資訊請關注PHP中文網其他相關文章！